Nylon Chain Coupling (Wrapped type coupling )
- Economical, flexible couplings consisting of sprockets and typical engineering plastic chains made of polyacetal.
- Economical, flexible couplings consisting of sprockets and typical engineering plastic chains made of polyacetal.
- ・Applicable shaft diameter :9.5Φmm~Φ55mm
- ・Torque range :6.9~255N・m
Standard type Structure & Features
-
・Compatible with short inter-shaft distance
This coupling consists of two sprockets that are connected with nylon chains, so it can be installed even when the distance between the shafts is short, allowing for more compact design of your equipment.
-
・Easy to install and remove
Can be installed by simply winding the nylon chains over the sprockets, and inserting a joint pin.
Also, you can cut the edge without moving the drive unit and driven unit for maintenance of your equipment.
-
・Higher torque available with no length change
The coupling transmissible torque can be raised by increasing the number of sprocket teeth. Without changing the inter-shaft distance of your equipment, you can increase the coupling size.
-
・Nylon chain sspecifications :
Material / Polyacetal Joint pin material / Carbon steel Color / White
Standard type Line-up
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
---|---|---|---|---|---|
CN310 | Φ12 | 6.86 | CN416 | Φ30 | 64.3 |
CN311 | Φ14 | 8.82 | CN417 | Φ32 | 72.5 |
CN312 | Φ16.5 | 10.8 | CN418 | Φ35 | 81.3 |
CN313 | Φ18 | 12.7 | CN419 | Φ39.5 | 90.5 |
CN314 | Φ16.5 | 14.7 | CN610 | Φ30 | 102 |
CN315 | Φ19 | 16.7 | CN611 | Φ32 | 116 |
CN316 | Φ20 | 18.6 | CN612 | Φ32 | 132 |
CN317 | Φ24 | 21.6 | CN613 | Φ35 | 149 |
CN410 | Φ16.5 | 25.4 | CN614 | Φ39.5 | 166 |
CN411 | Φ20 | 30.6 | CN615 | Φ45.5 | 181 |
CN412 | Φ22 | 36.4 | CN616 | Φ47.5 | 201 |
CN413 | Φ20 | 42.6 | CN617 | Φ47.5 | 218 |
CN414 | Φ24 | 49.3 | CN618 | Φ55 | 236 |
CN415 | Φ28.5 | 56.6 | CN619 | Φ55 | 255 |
-
※Allowable transmitted torque at up to 100 rpm.
E Type Features and Products line-up
- The body is made of extra super duralumin.
- ・Allows for 30% higher torque than the standard type through its new tooth configuration.
- ・Applicable shaft diameter :Φ11mm~Φ39.5mm
- ・Torque range :36.3~118N・m
- ・High torque :The newly developed tooth configuration contributed to the increased transmissible torque by about 30%. (comparison with the standard type )
- ・Longevity :Delivers more than 3 times the standard type service life.
- ・Super-lightweight :The body uses extra super duralumin, allowing for 50% lighter weight than the standard type.
- ・Easy mounting :Capable of allowing almost 2 times the standard type misalignment at the time of installation.
- ・Nylon chain sspecifications :Material / Polyacetal Joint pin material / Polyacetal Color / Yellow
Line-up
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
---|---|---|---|---|---|
CNE410 | Φ16.5 | 36.3 | CNE415 | Φ28.5 | 73.5 |
CNE411 | Φ20 | 42.6 | CNE416 | Φ30 | 83.6 |
CNE412 | Φ22 | 49.1 | CNE417 | Φ32 | 94.3 |
CNE413 | Φ20 | 57.5 | CNE418 | Φ35 | 106 |
CNE414 | Φ24 | 64.1 | CNE419 | Φ39.5 | 118 |
-
※Allowable transmitted torque at up to 100 rpm.
H Type Features and Products line-up
- Nylon chain coupling with superior environmental and chemical resistance.
- ・The body is made of extra super duralumin, and the chain uses Hytrel®
- ・Applicable shaft diameter :Φ11mm~Φ39.5mm
- ・Torque range :12.7~45.3N・m
- ・Environment resistance :Employs Hytrel® for the chain material. Can be used in a wide temperature range from -20℃ to +110℃.
- ・Super-lightweight :The body uses extra super duralumin, allowing for 50% lighter weight than the standard type.
- ・Easy mounting :Can accommodate nearly twice as much mounting misalignment as the standard type.
- ・Eco-friendly :The chain is entirely made of plastic and easy to dispose of after use.
- ・Nylon chain sspecifications :Material / Hytrel Joint pin material / Hytrel Color / Ivory
Line-up
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
Model No. | Maximum Shaft Bore Diameter | Allowable transmission torque N・m |
---|---|---|---|---|---|
CNH410 | Φ16.5 | 12.7 | CNH415 | Φ28.5 | 28.3 |
CNH411 | Φ20 | 15.3 | CNH416 | Φ30 | 32.2 |
CNH412 | Φ22 | 18.2 | CNH417 | Φ32 | 36.3 |
CNH413 | Φ20 | 21.3 | CNH418 | Φ35 | 40.6 |
CNH414 | Φ24 | 24.7 | CNH419 | Φ39.5 | 45.3 |
-
※Allowable transmitted torque at up to 100 rpm.
Catalogs ・Instruction Manuals
Model No. examples
CN | E | 4 | 15 |
| Series |
| Type |
| Chain size |
| Teeth and Links |
Blank: Standard type E:E Type H:H Type |
List of Model Numbers
※Click the model No. for detailed information.
Standard type (Stock item with plain bore ) | E Type (With plain bore ) | H Type (With plain bore ) | ||
---|---|---|---|---|
CN310 | CNE410 | CNH410 | ||
CN311 | CNE411 | CNH411 | ||
CN312 | CNE412 | CNH412 | ||
CN313 | CNE413 | CNH413 | ||
CN314 | CNE414 | CNH414 | ||
CN315 | CNE415 | CNH415 | ||
CN316 | CNE416 | CNH416 | ||
CN317 | CNE417 | CNH417 | ||
CN410 | CNE418 | CNH418 | ||
CN411 | CNE419 | CNH419 | ||
CN412 | ||||
CN413 | ||||
CN414 | ||||
CN415 | ||||
CN416 | ||||
CN417 | ||||
CN418 | ||||
CN419 | ||||
CN610 | ||||
CN611 | ||||
CN612 | ||||
CN613 | ||||
CN614 | ||||
CN615 | ||||
CN616 | ||||
CN617 | ||||
CN618 | ||||
CN619 |