Drawing Library   Linear actuator

U Series

Model No.  LPUB~/LPUC~

Go to Model No. Selection

The smaller, lighter U Series Power Cylinder with more than 6 tons rated thrust. (Large capacity: More than 58.8kN )

  • ・Lightweight and compact :
    Thanks to newly developed special ball screws and bearings, we succeeded in reducing the total length by a max. of 10% and the mass 35% compared with the previous model (T series). The smaller size and lighter weight makes it easy to replace hydraulic cylinders.
  • ・Complete line-up available :
    We added a new model with 50 tons rated thrust, which makes it easy to replace large hydraulic cylinders with a 250 mm inner diameter.
  • ・Improved cost performance :
    In addition to achieving cost reductions compared to previous models thanks to smaller and lighter parts, the power cylinder is electrical so it has much better power savings than hydraulic types, greatly reducing power consumption.
Rated Thrust kN

58.8~490

Speed mm/s

6.5/7.8~43/52

Stroke mm

500~2000

U Series Multi Type

Model No.  LPUA□□□□B~ LPUC□□□□B~

Go to Model No. Selection

The Multi Type Power Cylinder is capable of synchronizing multiple cylinders with one motor. (Large capacity: More than 58.8kN )

  • ・High-speed Operation :
    MTO products can achieve high-speed operation up to 150mm/s.
  • ・Safe :
    A thrust detection unit can be built-in to detect overload and protect the machine. (LPUC)
  • ・Rugged construction :
    The actuator area supporting the load and the reducer area are separated. Fluctuating loads will not affect the contact on the gear teeth.
  • ・Drive multiple units together :
    Using an input shaft with enough strength allows synchronous operation of multiple units.
  • ・Capable of oscillation :
    The input shaft and trunnion area have the same shaft center, allowing for swinging motion during interlocked operation.
Allowable Thrust kN

58.8~313

Speed mm/s

6.5/7.8~43/52

Stroke mm

500~2000

T Series

Model No.  LPTB~/LPTC~

Go to Model No. Selection

A power cylinder in the medium thrust zone that can be used with an AC (alternating current) power supply. (Medium capacity 39.2kN or less )

  • ・Two safety mechanisms :
    You can choose the type according to the protection method. TB Type has a built-in wet slip clutch. The TC Type comes with a thrust detecting limit switch.
  • ・Wide variation :
    A wide range of standard models are available depending on the application, thrust, and speed.
    You can choose the thrust from between 2.45kN and 39.2 kN, and the speed from 9mm/s and 120mm/s.
  • ・Positive actuation :
    A highly-reliable safety device is built into all series so as to work effectively against overload.
  • ・Wide variety of options :
    Two types of stroke adjusting limit switches (external and internal types) and stroke sensors (potentiometer and rotary encoder types) are available, allowing for much easier control by a sequencer.
Rated Thrust kN

2.45~39.2

Speed mm/s

9/11~100/120

Stroke mm

200~1500

T Series Multi Type

Model No.  LPTB□□□□B~ LPTC□□□□B~

Go to Model No. Selection

Capable of synchronizing multiple cylinders with one motor. (Medium capacity 39.2kN or less )

  • ・Safe :
    A thrust detection unit can be built-in to detect overload and protect the machine. (LPTC)
  • ・Rugged construction :
    The actuator area supporting the load and the reducer area are separated. Fluctuating loads will not affect the contact on the gear teeth.
  • ・Drive multiple units together :
    Using an input shaft with enough strength allows synchronous operation of multiple units.
  • ・Capable of oscillation :
    The input shaft and trunnion area have the same shaft center, allowing for swinging motion during interlocked operation.
Allowable Thrust kN

4.94~39.2

Speed mm/s

72~120

Stroke mm

200~1500

Worm Series

Model No.  LPWB~

Go to Model No. Selection

Worm series is the perfect power cylinder to replace hydraulic cylinders.

  • ・Worm Series LPWB provides large thrust by using a high precision worm gear and a highly efficient ball screw manufactured with technology based on nearly a century of manufacturing tradition.
  • ・Clean :
    There are no hydraulic pumps or pipes, so no worries about oil leakage from the connecting parts.
  • ・Easy installation :
    No need for hydraulic pumps and pipes. Can be operated just by connecting a three-phase power source.
  • ・Accurate control :
    Changing speeds and accurate positioning are possible by using an inverter.
  • ・Low cost :
    Reduces costs by significantly reducing the number of parts.
  • ・High load capacity :
    Can be used with large loads like jacks can thanks to its special steel alloy.
Rated Thrust kN

49~294

Speed mm/s

5~72(Reference )

Stroke mm

200~2000(Reference )

G Series

Model No.  LPG~

Go to Model No. Selection

A power cylinder with a small thrust zone that can be used with an AC (alternating current) power supply. (Capacity 3.00kN or less )

  • ・Wide variation :
    Approximately 9000 models are standardized, including 630 basic types and models with optional parts.
  • ・Stable, high efficiency, longevity :
    High efficiency has been achieved by employing nut material that has excellent compatibility with the aligning trapezoidal screw thread (centralizing screw) specially designed for the Power Cylinder, which provides stability and a long operating life.
  • ・The type of screw can be selected according to the application. :
    The Power Cylinder G Series basically uses a trapezoidal screw. For high frequency or long life operation, consider using the ball screw type.
  • ・Silent operation :
    Significantly reduced noise during startup and stopping through a quiet DC brake motor drive.
  • ・Excellent speed stability :
    Operations at a steady velocity is possible that is impervious to load fluctuations.
Rated Thrust N

700~3.00k

Speed mm/s

25/30~200/240

Stroke mm

100~1200

F Series

Model No.  LPF~

Go to Model No. Selection

A small thrust type power cylinder for driving with a DC (battery) power supply.

  • ・Compact, lightweight, efficient use of installation space :
    Compact design with the right angled connection between the actuating part and motor unit. Due to the right angled two-way clevis holes, you can choose from four mounting directions so as not to interfere with another machine.
  • ・Outdoor Use :
    This unit is ideal for outdoor applications, such as farming machines and vertical parking carousels.
  • ・Wide variety of options :
    Variety of options are available such as a position detecting unit and an overload detecting unit.
Rated Thrust N

100~6.00k

Speed mm/s

8~54

Stroke mm

50~600

Eco Series Servo Type

Model No.  LPES~

Go to Model No. Selection

Can support high-speed and high-precision operation so that the performance of the servo motor can be maximized.

  • ・Maximizing Servomotor Performance :
    The combination of a high-efficiency ball screw and highly rigid lightweight disk coupling maximizes the servomotor performance.
  • ・High Stopping Accuracy :
    The high-precision ball screw delivers high stopping accuracy. Repeated positioning accuracy is within ±0.02mm, and stopping accuracy is within ±0.1mm.
  • ・Benefits of Precision Planetary Reducer Type :
    By downsizing the servomotor you can save on initial costs with smaller peripheral devices such as an amplifier, while reducing running costs through lower power consumption.
  • ・Allows selection of the servomotor :
    Desired servomotors can be installed. Please specify the servomotor manufacturer or mount code when asking for a quotation.
  • ・High-Speed, Wide Thrust Range :
    Can be used at high-speed and in a wide thrust range.
Rated Thrust N

150~15.0k

Speed mm/s

1~333

Stroke mm

300~1000

Eco Series CDS Type

Model No.  LPE~

Go to Model No. Selection

Ideal for use in two-point operation such as air cylinders. Features self-contained functions that detect overcurrent.

  • ・Self-contained :
    With a spring built in the linear actuating part and the CDS (Current Detective System) mounted in the terminal box, overcurrent is detected even when press contact stops or in the case of overload, and the motor is automatically stopped.
    During stoppage, the pressing force is maintained by the built-in spring.
  • ・Lower running costs, environmentally-friendly :
    This electrically operated type consumes electricity only when used, allowing for economical operations. There is no need to operate a compressor all the time like in an air system, so a significant reduction in running costs can be expected.
  • ・High-Frequency Operation & Long Life :
    Capable of a maximum of 15 times/min high-frequency operation. With the ball screw, a long service life of 1 million strokes can be expected.
  • ・Simple operation :
    Can be operated just by connecting a three-phase power source. No limit switch for stroke adjustment is required, saving you the hassle of wiring. Also compatible with long-distance wiring.
Rated Thrust N

250~1.00k

Speed mm/s

90/90/110~160/190/200

Stroke mm

100~600

Mini Series

Model No.  LP~

Go to Model No. Selection
  • ・Stroke :100~300mm
  • ・Runs on a single phase power supply.
  • ・Designed for longevity
  • ・Wide variety of options
Rated Thrust N{kgf}

98.0{10}~392{40}



Speed mm/s

9/11~34/42

Click here for a list of all DXF files