技术资料 联轴器 选型及步骤
选型时的需注意事项和选型步骤请参考本页面内容。
选择可使用的产品系列或简易选型时请点击此处。
使用条件已基本确定，欲了解更为详细地选型方法时请点击此处。
爪式联轴器 L系列 选定
- (1)选型时的使用系数（表1），需根据原动机的种类和运转条件进行选择。
- (2)负荷转矩（T）乘以表1的使用系数（SF）计算得出修正转矩（T’），需选择容许转矩大于修正转矩的联轴器型号。(请参照下表)
- (3)所选定的联轴器型号，确认其最大轴孔径大于实际所需。不符合要求时，需另行选型、(请参照下表)
- (4)和电机直接连接使用时，请参考表2、表3的产品选型表。
转矩的计算方法
T = 9550 × P n T = 974 × P n
- T = 负载扭矩 N・m {kgf・m}
- P = 动力传递 kW
- n = 转速 r/min
- T' = 修正扭矩 N・m {kgf・m}
| 负载的性质 | 原动机的类型 | ||
|---|---|---|---|
| 涡轮电机 | 汽油发动机 柴油发动机 (6气筒以上) |
汽油发动机 柴油发动机 (6气筒未满) |
|
|
・无负荷时间、稳定 ・无正逆运行 ・运行时间 = 8小时左右/天 ・低转矩启动 |
1.0 | 1.5 | 2.0 |
|
・有中度的负荷变动 ・有中度的冲击负荷 ・运行时间 = 8小时左右/天 ・无正逆运行(使用普通驱动时的适用SF) |
1.5 | 2.0 | 2.5 |
|
・有剧烈的冲击负荷 ・有大幅度的负荷变动 ・运行时间 = 8小时左右/天 ・有正逆运行 ・大转矩启动 |
2.0 | 2.5 | 3.0 |
*运行时间＝16-24小时/天的，需将使用系数提高一个等级。
| 50Hz 电机 定格输出 kW |
2极 3000r/min | 4极 1500r/min | 6极 1000r/min | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | |||||||
| 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | |||||||
| 联轴器型号 | 联轴器型号 | 联轴器型号 | |||||||||||||
| 0.1 | 11 | 0.6 {0.06} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
||||||||||
| 0.2 | 11 | 0.6 {0.06} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
11 | 1.3 {0.13} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 1.9 {0.19} |
L050-S L050A-S |
L050-S L050A-S |
L070-S L070A-S |
| 0.4 | 14 | 1.3 {0.13} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 2.5 {0.26} |
L050-S L050A-S |
L050-H L070A-S |
L050-H L075A-S |
19 | 3.8 {0.39} |
L070-S L070A-S |
L075-S L075A-S |
L075-S L075A-S |
| 0.75 | 19 | 2.4 {0.24} |
L070-S L070A-S |
L070-S L070A-S |
L070-S L070A-S |
19 | 4.8 {0.49} |
L070-S L070A-S |
L070-M L075A-S |
L070-H L075A-S |
24 | 7.2 {0.73} |
L075-S L075A-S |
L075-S L075A-S |
L075-M L090A-S |
| 1.5 | 24 | 4.8 {0.49} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
24 | 9.5 {0.97} |
L075-S L075A-S |
L075-M L090A-S |
L075-H L095A-S |
28 | 14.7 {1.5} |
L090-S L090A-S |
L090-M L095A-S |
L090-H L100A-S |
| 2.2 | 24 | 7.0 {0.71} |
L075-S L075A-S |
L075-S L075A-S |
L075-M L090A-S |
28 | 14.0 {1.43} |
L090-S L090A-S |
L090-M L095A-S |
L090-H L100A-S |
28 | 20.6 {2.1} |
L095-S L095A-S |
L099-S L100A-S |
L099-M L100A-S |
| 3.7 | 28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
28 | 23.5 {2.4} |
L095-S L095A-S |
L090-H L100A-S |
L090-H L100A-S |
38 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 5.5 | 38 | 17.6 {1.8} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 52.9 {5.4} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 7.5 | 38 | 23.5 {2.4} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 48.0 {4.9} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 71.5 {7.3} |
L110-S L110A-S |
L110-S L110A-S |
L110-H |
| 11 | 42 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 69.6 {7.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-H | 42 | 105 {10.7} |
L110-S L110A-S |
L150-M | L150-M |
| 15 | 42 | 48.0 {4.9} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 95.1 {9.7} |
L110-S L110A-S |
L110-H | L110-H | 48 | 143 {14.6} |
L190-S | L190-M | L190-M |
| 18.5 | 42 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-M | 48 | 118 {12.0} |
L150-S | L150-S | L150-H | 55 | 176 {18.0} |
L190-S | L190-M | L190-H |
| 22 | 48 | 69.6 {7.1} |
L110-S L110A-S |
L110-S L110A-S |
L150-S | 48 | 140 {14.3} |
L150-S | L150-M | L150-H | 55 | 210 {21.4} |
L225-S | L225-M | L225-H |
| 30 | 55 | 95.1 {9.7} |
L190-S | L190-S | L190-S | 55 | 191 {19.5} |
L190-S | L190-M | L190-H | 60 | 286 {29.2} |
L225-M | L225-H | L225-H |
| 37 | 55 | 118 {12.0} |
L190-S | L190-S | L190-M | 60 | 235 {24.0} |
L225-S | L225-M | L225-H | |||||
| 45 | 55 | 143 {14.6} |
L190-S | L190-M | L190-M | 60 | 286 {29.2} |
L225-H | L225-H | L225-H | |||||
| 55 | 55 | 175 {17.9} |
L190-S | L190-M | L190-H | ||||||||||
| 75 | 55 | 239 {24.4} |
L190-M | L190-H | L190-H | ||||||||||
| 90 | 55 | 286 {29.2} |
L190-M | L190-H | L190-H | ||||||||||
| 110 | 55 | 350 {35.7} |
L190-H | L190-H | L225-H | ||||||||||
| 132 | 55 | 420 {42.9} |
L190-H | L225-H | |||||||||||
- 注）1. 选型时需确认电机的基本特性。
- 注）2. 标记为现有库存，均为经标准轴孔加工的轮毂。
| 60Hz 电机 定格输出 kW |
2极 3600r/min | 4极 1800r/min | 6极 1200r/min | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | 电机轴径 mm |
电机定格扭矩 N・m {kgf・m} |
使用系数 | |||||||
| 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | |||||||
| 联轴器型号 | 联轴器型号 | 联轴器型号 | |||||||||||||
| 0.1 | 11 | 0.5 {0.05} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
||||||||||
| 0.2 | 11 | 0.5 {0.05} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
11 | 1.0 {0.1} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 1.6 {0.16} |
L050-S L050A-S |
L050-S L050A-S |
L050-H L070A-S |
| 0.4 | 14 | 1.0 {0.1} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 2.0 {0.2} |
L050-S L050A-S |
L050-S L050A-S |
L050-H L070A-S |
19 | 2.9 {0.3} |
L070-S L070A-S |
L070-S L070A-S |
L075-S L075A-S |
| 0.75 | 19 | 2.0 {0.2} |
L070-S L070A-S |
L070-S L070A-S |
L070-S L070A-S |
19 | 3.9 {0.4} |
L070-S L070A-S |
L070-M L075A-S |
L070-H L075A-S |
24 | 5.9 {0.6} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
| 1.5 | 24 | 3.9 {0.4} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
24 | 7.8 {0.8} |
L075-S L075A-S |
L075-S L075A-S |
L075-H L090A-S |
28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
| 2.2 | 24 | 5.9 {0.6} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
28 | 17.6 {1.8} |
L090-M L095A-S |
L090-H L100A-S |
L090-H L100A-S |
| 3.7 | 28 | 9.8 {1.0} |
L090-S L090A-S |
L090-S L090A-S |
L090-M L095A-S |
28 | 19.6 {2.0} |
L090-M L095A-S |
L090-H L100A-S |
L090-H L100A-S |
38 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 5.5 | 38 | 14.7 {1.5} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 44.1 {4.5} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 7.5 | 38 | 19.6 {2.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 40.2 {4.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 59.8 {6.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-M |
| 11 | 42 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-M | 42 | 87.2 {8.9} |
L110-S L110A-S |
L110-M | L110-H |
| 15 | 42 | 40.1 {4.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 79.4 {8.1} |
L110-S L110A-S |
L110-M | L110-H | 48 | 120 {12.2} |
L150-S | L150-M | L150-H |
| 18.5 | 42 | 49.0 {5.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
48 | 98.0 {10.0} |
L110-S L110A-S |
L150-S | L150-M | 55 | 147 {15.0} |
L190-S | L190-M | L190-H |
| 22 | 48 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L150-S | 48 | 117 {11.9} |
L150-S | L150-M | L150-H | 55 | 175 {17.9} |
L225-S | L225-S | L225-M |
| 30 | 55 | 79.4 {8.1} |
L190-S | L190-S | L190-S | 55 | 159 {16.2} |
L190-S | L190-M | L190-H | 60 | 239 {24.4} |
L225-S | L225-M | L225-H |
| 37 | 55 | 98.0 {10.0} |
L190-S | L190-S | L190-S | 60 | 196 {20.0} |
L225-S | L225-M | L225-M | |||||
| 45 | 55 | 120 {12.2} |
L190-S | L190-S | L190-M | 60 | 239 {24.4} |
L225-S | L225-M | L225-H | |||||
| 55 | 55 | 146 {14.9} |
L190-S | L190-M | L190-H | ||||||||||
| 75 | 55 | 199 {20.3} |
L190-M | L190-H | L190-H | ||||||||||
| 90 | 55 | 239 {24.4} |
L190-M | L190-H | L190-H | ||||||||||
| 110 | 55 | 292 {29.8} |
L190-H | L190-H | L225-H | ||||||||||
| 132 | 55 | 350 {35.7} |
L190-H | L190-H | L225-H | ||||||||||
- 注）1. 选型时需确认电机的基本特性。
- 注）2. 标记为现有库存，均为经标准轴孔加工的轮毂。
